[Fri Dec 16 18:42:03 2011] Detection parameters: Position = (204.4, 250.3) = 23 24 19.92 -55 49 7.9 Extent = 10.9" x 10.9", rotation angle = 0 degrees Source counts = 26.3 +/- 7.0 Background counts = 3.5 Rate = 0.005 +/- 0.001 [Fri Dec 16 18:42:03 2011] Off-axis axis estimate = 7.66' [Fri Dec 16 19:05:46 2011] Using EEF radius (= 10.26 ")to estimate initial spatial extent for simple fitting [Fri Dec 16 19:05:46 2011] Setting initial spatial extent for simple fitting to maximum allowed for this pass [Fri Dec 16 19:05:46 2011] Initial guess for spatial extent in simple fitting = 10.26" [Fri Dec 16 19:05:46 2011] source mask rpix=2.4, npix_max = 32, mask sum = 30, frac = 0.918 [Fri Dec 16 19:05:46 2011] Giving source the simple spatial ID 3 for pass 0, mean size = 10.26" [Fri Dec 16 19:11:11 2011] fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_src3.ximg exists [Fri Dec 16 19:11:11 2011] Warning: poor agreement between model and actual number of counts may be indicative of a poor fit in csv/fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_src3.csv [Fri Dec 16 19:11:11 2011] fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_src3_1.ximg exists [Fri Dec 16 19:11:11 2011] Warning: poor agreement between model and actual number of counts may be indicative of a poor fit in csv/fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_src3.csv [Fri Dec 16 19:11:11 2011] It looks like the fit did not converge You should probably delete fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_src3_1.ximg Either tweak this fit manually starting from fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_src3.ximg or adjust the simplespatial fit parameters in $XASSIST/data/missions/*/*/spatial.dat and re-run simplespatial fitting after setting file recreation parameter to yes [Fri Dec 16 19:11:11 2011] fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_tfrozen_src3.ximg exists [Fri Dec 16 19:11:11 2011] fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_tfrozen_src3_1.ximg exists [Fri Dec 16 19:11:11 2011] Fit fullrun_mos2_xmm0505380801_pi300-10000_cl_pass0_tfrozen_src3 appears to have run properly [Fri Dec 16 19:11:15 2011] Spatial fit model total counts = 61.222000, observed total counts = 63.000000 [Fri Dec 16 19:11:15 2011] Offset between fit and detection position for source 4 = 4.988325 pixels Spatial fit parameters: Offset between fit and detection position for source 4 = 4.988325 pixels Position = (200.1, 252.9) = 23 24 22.10 -55 48 56.5 Extent = 20.5 (20.5-41.0)", rotation angle = 0 Source counts = 62.0 +/- 7.9 Background counts = 0.0 Rate = 0.007 +/- 0.0008 Deleting source due to low signal-to-noise ratio